Wednesday, June 10, 2009

Trick My Truck & SUV - Chevrolet Tahoe Add Ons to Increase Horsepower and Gas Mileage

Chevrolet has perfected a huge selling success with its Tahoe and Suburban SUV. With a wide array of trim packages and powertrain choices, there's a little of everything for folks of all walks of life. But as gas prices start to climb and more people looking for more fuel efficient alternatives, owners are looking for cheap ways to enhance what they've got without going to the extreme of trading or downsizing into something less favorable. The aftermarket world for performance enhancing parts is huge with the Chevrolet Tahoe and is certainly worth the research to find the right products for your SUV. Here is a brief list of inexpensive do-it-yourself items you can buy and install in an afternoon.

First, an easy to find item is a higher flowing performance air filter. Manufactured by well known companies such as K&N, airaid and AEM, these products can be purchased at any auto retailer like Wal-Mart, AutoZone and Pep Boys. What a performance filter does is replace your existing restrictive stock filter with a higher flowing unit. The better the engine can breathe, the more horsepower and better gas mileage. Tests have shown a 8-10 HP increase and a 1-3 mpg upswing in a 5.3 V8 Tahoe. Aside from the gains, maintenance will be cut down as well as these filters are cleanable and reusable too. In essence, don't leave this cheap part off your list, they only retail for $35-55!

Next, a performance exhaust system is another cheap way to free up some more of those HP's and overall gas mileage in your old or new Tahoe. Kits are available from manufacturers like flowmaster, borla, and Bassani for all engine size Tahoes from the early 1995 models to the newer 2010's. Kits come complete with all the hardware and instructions. All you have to supply are basic hand tools and an afternoon's amount of time to get it all together. Your Tahoe will thank you because the engine will dispel all of the burnt gases easier and you will get that nice deep throaty sound once made popular in muscle cars. Gain more power and a few more mpg's with this must have modification.

And lastly, no Chevrolet Tahoe or GMC Yukon will come complete without a performance chip from Hypertech or Superchips. Performance chips retail at around $80-100 and only take about 20 minutes to install using basic handtools. What a performance chip does for your ride is that it will enhance your transmission's shift points for better efficiency and less wear and tear. A good performance chip will also enhance your truck or SUV's fuel curve to gain more mpg's too. A performance chip will compliment the other performance parts and won't void any existing warranty.

And so, that is a brief list of some of the most popular and tested parts one must buy for their Tahoe or Yukon. Altogether, you should see about a 30-40 horsepower increase and about a 5-7 mpg gain with all the mods. With summer just around the corner, motorists could use more of their hard earned bucks toward more important activities. But if you want to take modifications a step further, drivers have been converting their truck and SUV into hybrid type vehicles. I've seen water/gas conversions and the popular electric/gas hybrid conversion made popular by Toyota and Honda. The IRS will even pay you tax credits for driving a clean fuel vehicle, nothing but positive money savings here. For more information on how you can convert your truck and SUV now, please feel free to visit my site below.

Chevrolet has perfected a huge selling success with its Tahoe and Suburban SUV. With a wide array of trim packages and powertrain choices, there's a little of everything for folks of all walks of life. But as gas prices start to climb and more people looking for more fuel efficient alternatives, owners are looking for cheap ways to enhance what they've got without going to the extreme of trading or downsizing into something less favorable. The aftermarket world for performance enhancing parts is huge with the Chevrolet Tahoe and is certainly worth the research to find the right products for your SUV. Here is a brief list of inexpensive do-it-yourself items you can buy and install in an afternoon.

First, an easy to find item is a higher flowing performance air filter. Manufactured by well known companies such as K&N, airaid and AEM, these products can be purchased at any auto retailer like Wal-Mart, AutoZone and Pep Boys. What a performance filter does is replace your existing restrictive stock filter with a higher flowing unit. The better the engine can breathe, the more horsepower and better gas mileage. Tests have shown a 8-10 HP increase and a 1-3 mpg upswing in a 5.3 V8 Tahoe. Aside from the gains, maintenance will be cut down as well as these filters are cleanable and reusable too. In essence, don't leave this cheap part off your list, they only retail for $35-55!

Next, a performance exhaust system is another cheap way to free up some more of those HP's and overall gas mileage in your old or new Tahoe. Kits are available from manufacturers like flowmaster, borla, and Bassani for all engine size Tahoes from the early 1995 models to the newer 2010's. Kits come complete with all the hardware and instructions. All you have to supply are basic hand tools and an afternoon's amount of time to get it all together. Your Tahoe will thank you because the engine will dispel all of the burnt gases easier and you will get that nice deep throaty sound once made popular in muscle cars. Gain more power and a few more mpg's with this must have modification.

And lastly, no Chevrolet Tahoe or GMC Yukon will come complete without a performance chip from Hypertech or Superchips. Performance chips retail at around $80-100 and only take about 20 minutes to install using basic handtools. What a performance chip does for your ride is that it will enhance your transmission's shift points for better efficiency and less wear and tear. A good performance chip will also enhance your truck or SUV's fuel curve to gain more mpg's too. A performance chip will compliment the other performance parts and won't void any existing warranty.

And so, that is a brief list of some of the most popular and tested parts one must buy for their Tahoe or Yukon. Altogether, you should see about a 30-40 horsepower increase and about a 5-7 mpg gain with all the mods. With summer just around the corner, motorists could use more of their hard earned bucks toward more important activities. But if you want to take modifications a step further, drivers have been converting their truck and SUV into hybrid type vehicles. I've seen water/gas conversions and the popular electric/gas hybrid conversion made popular by Toyota and Honda. The IRS will even pay you tax credits for driving a clean fuel vehicle, nothing but positive money savings here. For more information on how you can convert your truck and SUV now, please feel free to visit my site below.

The Best Brands For Used Trucks

The durability of trucks, depends on the specifications of each truck. In the other words, the best quality and best brand of truck, depends on its efficiency, reliability and work output. Used truck dealers, can be easily located via factories and websites (internet).

There are several used truck brands, such as Volvo trucks, Mercedes-Benz trucks, SCANIA trucks, Man trucks and IVECO trucks. Though different used trucks are available in the market, Mercedes-Benz trucks and IVECO trucks are the only trucks have a unique features related to "heavy-duty" capacity and unique service purpose.

Mercedes-Benz Trucks
Mercedes-Benz used trucks have the overall features needed for both commercial and private services. A Mercedes-Benz used truck is useful for load transportation in particular. If you are looking for a used truck for load transportation purposes you should include this brand on your shopping list. Mercedes-Benz trucks, "both flat and straight engine" are easy to drive. They also have different models and body shapes, for every specific purpose. Another feature that makes Mercedes unique among other used trucks is that they are very economical. They typically consume no more than 20litres of diesel per 500km journey. In comparison other used trucks out there consume more oil; usually 36 litres of diesel per 150km.

Furthermore, transporting with a Mercedes-Benz truck is always a blissful journey. They come with a well-built engine which makes the driving more comfortable during a long journey.

IVECO Trucks
IVECO trucks also have some spectacular features among other used truck brands. One unique feature that distinguishes IVECO from other used truck brands is it also has a 'heavy-duty' capacity. Many IVECO truck drivers can confirm the flexibility and simplicity of this vehicle. IVECO trucks not only have a price that is affordable, but are also efficient and easily maintained. IVECO trucks are well known for their carriage purposes too. They are strong enough to carry a load range from 10,000kg to 50,000kg, with ease. In addition this durable truck has low diesel consumption. You can purcase IVECO trucks through their factory centers, whereby you will can ask to be shown a wide range of quality used trucks. Additional financing and warranty options and backed up by the official IVECO network service.

In conclusion, getting the best used truck for your specific purposes can be a realistic and successful investment. It is best to ensure you consider all the realistic requirements you have versus the capabilities and specifications of each truck.

Labels:

The durability of trucks, depends on the specifications of each truck. In the other words, the best quality and best brand of truck, depends on its efficiency, reliability and work output. Used truck dealers, can be easily located via factories and websites (internet).

There are several used truck brands, such as Volvo trucks, Mercedes-Benz trucks, SCANIA trucks, Man trucks and IVECO trucks. Though different used trucks are available in the market, Mercedes-Benz trucks and IVECO trucks are the only trucks have a unique features related to "heavy-duty" capacity and unique service purpose.

Mercedes-Benz Trucks
Mercedes-Benz used trucks have the overall features needed for both commercial and private services. A Mercedes-Benz used truck is useful for load transportation in particular. If you are looking for a used truck for load transportation purposes you should include this brand on your shopping list. Mercedes-Benz trucks, "both flat and straight engine" are easy to drive. They also have different models and body shapes, for every specific purpose. Another feature that makes Mercedes unique among other used trucks is that they are very economical. They typically consume no more than 20litres of diesel per 500km journey. In comparison other used trucks out there consume more oil; usually 36 litres of diesel per 150km.

Furthermore, transporting with a Mercedes-Benz truck is always a blissful journey. They come with a well-built engine which makes the driving more comfortable during a long journey.

IVECO Trucks
IVECO trucks also have some spectacular features among other used truck brands. One unique feature that distinguishes IVECO from other used truck brands is it also has a 'heavy-duty' capacity. Many IVECO truck drivers can confirm the flexibility and simplicity of this vehicle. IVECO trucks not only have a price that is affordable, but are also efficient and easily maintained. IVECO trucks are well known for their carriage purposes too. They are strong enough to carry a load range from 10,000kg to 50,000kg, with ease. In addition this durable truck has low diesel consumption. You can purcase IVECO trucks through their factory centers, whereby you will can ask to be shown a wide range of quality used trucks. Additional financing and warranty options and backed up by the official IVECO network service.

In conclusion, getting the best used truck for your specific purposes can be a realistic and successful investment. It is best to ensure you consider all the realistic requirements you have versus the capabilities and specifications of each truck.

Labels:

Thursday, May 28, 2009

Getting Your Restaurant Supplies From Equipment Companies

If this is the first time that you are starting up a food business, you should know what you need to look into to make it successful as much as possible. Aside from your staff and your managing techniques as a business owner, it is essential that you obtain the right supplies for your restaurant to be more productive in terms of food preparation as well as time management.

Since you are starting up a business, you might be thinking that you do not have enough budget for high standard supplies that are usually branded and are of high quality. The good news is that, you will still have other options aside from purchasing your equipment from restaurant supply companies, fortunately they are not the only ones available in the equipment business.

However, before you look for a supplier, what you need to consider in obtaining the supplies for your food business. First, you need to consider the quality of the supplies and equipment that the company is offering you. Then you have to make sure that the equipment is durable enough to last for years. You should also look into the proper customer care that these companies provide. You will know from there if they are capable of providing you the right service when it comes to customer relations.

One way of finding an affordable and trust worthy company, is through researching online. Usually these restaurant supply companies have their own websites where you can look into those supplies and equipment that they offer. Some will provide you with a wide variety of choices and even wholesale discounts. That is why more and more food businesses rely on getting their equipment online because they do not have to worry about the overhead expenses which may add up to the cost of the supplies and the equipment ordered.

Before purchasing your supplies, you have to make sure that you inspect the products physically. If physical inspection is not possible, make sure that the equipment store entitles you for a money back guarantee, this assures you that what they are selling you are supplies that are guaranteed to last for a longer period of time.

I've created a Wholesale Kitchen Supplies List for anyone who would like to get excellent Prices and Information of Supplies right now. This list is designed to help you start getting the products and information quicker than you ever thought possible. You'll have a good solid information in the shortest amount of time possible. You can find this list at http://www.CindyKitchen.com

Article Source: http://EzineArticles.com/?expert=Cindy_Hansen

Labels:

If this is the first time that you are starting up a food business, you should know what you need to look into to make it successful as much as possible. Aside from your staff and your managing techniques as a business owner, it is essential that you obtain the right supplies for your restaurant to be more productive in terms of food preparation as well as time management.

Since you are starting up a business, you might be thinking that you do not have enough budget for high standard supplies that are usually branded and are of high quality. The good news is that, you will still have other options aside from purchasing your equipment from restaurant supply companies, fortunately they are not the only ones available in the equipment business.

However, before you look for a supplier, what you need to consider in obtaining the supplies for your food business. First, you need to consider the quality of the supplies and equipment that the company is offering you. Then you have to make sure that the equipment is durable enough to last for years. You should also look into the proper customer care that these companies provide. You will know from there if they are capable of providing you the right service when it comes to customer relations.

One way of finding an affordable and trust worthy company, is through researching online. Usually these restaurant supply companies have their own websites where you can look into those supplies and equipment that they offer. Some will provide you with a wide variety of choices and even wholesale discounts. That is why more and more food businesses rely on getting their equipment online because they do not have to worry about the overhead expenses which may add up to the cost of the supplies and the equipment ordered.

Before purchasing your supplies, you have to make sure that you inspect the products physically. If physical inspection is not possible, make sure that the equipment store entitles you for a money back guarantee, this assures you that what they are selling you are supplies that are guaranteed to last for a longer period of time.

I've created a Wholesale Kitchen Supplies List for anyone who would like to get excellent Prices and Information of Supplies right now. This list is designed to help you start getting the products and information quicker than you ever thought possible. You'll have a good solid information in the shortest amount of time possible. You can find this list at http://www.CindyKitchen.com

Article Source: http://EzineArticles.com/?expert=Cindy_Hansen

Labels:

Starting and Growing Business With CNC Turning Center Financing and Leasing

The CNC turning machine is just the machine you need if you are into work that involves heavy machinery and requires a lot of precision. This is a special kind of machine which enables you to spin blocks of material and bring them to a desired shape and size. Although the turning and spinning bit can be achieved manually, it takes up an immense amount of resources and time. Instead, you should go for computerized CNC turning machines which will enable you get great results.

The turning process basically requires you to place the material on the lathe and then employing the cutting tool. The cutting tool has to be kept at work until you get the depth and dimension that you wanted. One among the many benefits of the turner is that it enables you to cut the material both from the inside and the outside. All you will have to do is to provide the computer with the basic instructions and numbers and then you will see great results. You can have entire control of the machine by using the computer that operates it. This tool has numerous utilities and is a great investment. However, it is quite an expensive machine and most business owners do not begin with a capital big enough to invest in CNC machines. If this is the problem, then you should go for financing.

The turning process is capable of cutting metal into different kinds of shapes. From plain surface to taper ends to contours, it can do it all. So what are the uses of metals cut into various shapes by the CNC turner? They are used to make shafts, hubs, brushes, pulleys, rods and numerous other things. Another great use of the CNC process is that it can be used to cut metals with a circular cross section. Its advanced software tool helps to cut these machines perfectly for industry use. Software tools go a long way in cost cutting but they do have another disadvantage. It puts a limit to the number of designs that you can get otherwise.

The primary reason why these turning machines are so popular is that they enable you to get perfect end product at really cost effective prices. This is why the industry places its trust in this machine.

The CNC turning centers are very useful for cutting, shaping and creating machine parts. However, this kind of a perfect tool comes at a certain cost. It is quite expensive. So if you are starting your business and really need this machine, you should go for turning center financing. There are many financing companies that are ready to provide the money for buying these machines.

The CNC turning centers are controlled by a very advanced computer that gives you the accurate result that you desire. They work very well with any kind of job that you do. But since they are quite costly, you should go for CNC turning center financing. Numerous businesses have earned a lot of profit by investing in a CNC turning center or by getting hold of it through financing. So if you are starting off your business where you will require a high performance turner, you should go for the CNC turning center.

Chris Fletcher's page features more about new and used CNC Turning Center Financing and other finance topics. Visit him at: http://www.crestcapital.com/Catalog - - free instant quote & web calculator!

Article Source: http://EzineArticles.com/?expert=Chris_Mark_Fletcher
Visit more news on cnc machines at http://www.cnc-machines.org

Labels:

The CNC turning machine is just the machine you need if you are into work that involves heavy machinery and requires a lot of precision. This is a special kind of machine which enables you to spin blocks of material and bring them to a desired shape and size. Although the turning and spinning bit can be achieved manually, it takes up an immense amount of resources and time. Instead, you should go for computerized CNC turning machines which will enable you get great results.

The turning process basically requires you to place the material on the lathe and then employing the cutting tool. The cutting tool has to be kept at work until you get the depth and dimension that you wanted. One among the many benefits of the turner is that it enables you to cut the material both from the inside and the outside. All you will have to do is to provide the computer with the basic instructions and numbers and then you will see great results. You can have entire control of the machine by using the computer that operates it. This tool has numerous utilities and is a great investment. However, it is quite an expensive machine and most business owners do not begin with a capital big enough to invest in CNC machines. If this is the problem, then you should go for financing.

The turning process is capable of cutting metal into different kinds of shapes. From plain surface to taper ends to contours, it can do it all. So what are the uses of metals cut into various shapes by the CNC turner? They are used to make shafts, hubs, brushes, pulleys, rods and numerous other things. Another great use of the CNC process is that it can be used to cut metals with a circular cross section. Its advanced software tool helps to cut these machines perfectly for industry use. Software tools go a long way in cost cutting but they do have another disadvantage. It puts a limit to the number of designs that you can get otherwise.

The primary reason why these turning machines are so popular is that they enable you to get perfect end product at really cost effective prices. This is why the industry places its trust in this machine.

The CNC turning centers are very useful for cutting, shaping and creating machine parts. However, this kind of a perfect tool comes at a certain cost. It is quite expensive. So if you are starting your business and really need this machine, you should go for turning center financing. There are many financing companies that are ready to provide the money for buying these machines.

The CNC turning centers are controlled by a very advanced computer that gives you the accurate result that you desire. They work very well with any kind of job that you do. But since they are quite costly, you should go for CNC turning center financing. Numerous businesses have earned a lot of profit by investing in a CNC turning center or by getting hold of it through financing. So if you are starting off your business where you will require a high performance turner, you should go for the CNC turning center.

Chris Fletcher's page features more about new and used CNC Turning Center Financing and other finance topics. Visit him at: http://www.crestcapital.com/Catalog - - free instant quote & web calculator!

Article Source: http://EzineArticles.com/?expert=Chris_Mark_Fletcher
Visit more news on cnc machines at http://www.cnc-machines.org

Labels:

Monday, September 01, 2008

Industrial Design as a Profession

Some professions are more demanding that others. Some professions required the practitioner to be multi-disciplinary as well as multi-talented. Industrial design of one of such profession. This article is a description of Industrial Design as a profession and career path.

Industrial Design or ID as it it commonly known as, is a rather specialised profession. Contrary to popular misconception, an industrial designer does not design factory processes. Basically, industrial design is a creative profession . The scope of work deals with the innovative and aesthetic aspect of product design.

Why is it being said that Industrial designers are often required to be multi-talented? This is because, he or she have to be an artist, marketing expert and engineer all roll into one. This profession requires the fine balancing of hardcore practicality and refined sense of aesthetics.

For example, the outlook and functionality of many consumer products are dictated by the industrial designer. The Industrial Designer is at the forefront of the product development process.

Industrial design is a very passion driven profession. In another word, you will need to be passionate about the things that you do in industrial design. Without the passion, the nature of the job can be pressurizing and tedious. It can be tough going for someone who lacks the necessary drive and passion.

In the past, industrial designers rely almost entirely on manual drawing and sketching skills. However, with the advances in digital technology, industrial design now also rely on computer aided industrial design or CAID.

Well, in a nutshell, the nature of Industrial Design is as described above. Thank you for reading.

The author runs Joblense.com, a site which provides career profiles for many interesting jobs, including industrial design.

Article Source: http://EzineArticles.com/?expert=Shen_Gerald

Labels:

Some professions are more demanding that others. Some professions required the practitioner to be multi-disciplinary as well as multi-talented. Industrial design of one of such profession. This article is a description of Industrial Design as a profession and career path.

Industrial Design or ID as it it commonly known as, is a rather specialised profession. Contrary to popular misconception, an industrial designer does not design factory processes. Basically, industrial design is a creative profession . The scope of work deals with the innovative and aesthetic aspect of product design.

Why is it being said that Industrial designers are often required to be multi-talented? This is because, he or she have to be an artist, marketing expert and engineer all roll into one. This profession requires the fine balancing of hardcore practicality and refined sense of aesthetics.

For example, the outlook and functionality of many consumer products are dictated by the industrial designer. The Industrial Designer is at the forefront of the product development process.

Industrial design is a very passion driven profession. In another word, you will need to be passionate about the things that you do in industrial design. Without the passion, the nature of the job can be pressurizing and tedious. It can be tough going for someone who lacks the necessary drive and passion.

In the past, industrial designers rely almost entirely on manual drawing and sketching skills. However, with the advances in digital technology, industrial design now also rely on computer aided industrial design or CAID.

Well, in a nutshell, the nature of Industrial Design is as described above. Thank you for reading.

The author runs Joblense.com, a site which provides career profiles for many interesting jobs, including industrial design.

Article Source: http://EzineArticles.com/?expert=Shen_Gerald

Labels:

Mechanical Engineering, Mechanical Design and Drawing Services at Lowest Rates

Mechanical Engineering involves the Physical usage for mechanism and functioning, design, manufacturing, installation, operation and maintenance of mechanical systems such as boilers, condensers, heat engines, air conditioners & refrigerators, machine tools, thermal power stations etc.

Kinematics, dynamics, static, Energy conversion, Mechanics, Manufacturing and production, refrigeration and air conditioning are the foundation subjects of mechanical engineering. It also Engage its attention with other Engineering disciplines like Electrical engineering in electronics, Aeronautical Engineering in Fluid Mechanics, Civil Engineering in stress & Strain analysis, Computer Engineering in hardware manufacturing etc.

Accomplishing mechanical projects has always posed serious problems for companies, whether they need computer aided design such as electrical engineering, new industrial product design, or civil engineering of a new building.

Many people are familiar with online project marketplaces that connect businesses and individuals in need of services with skilled professionals to perform the work. Companies have long struggled with the engineering required to launch new products and build customized facilities. When you discuss the actual mechanical design of your next key product, or the structural engineering of a multi million dollar building, things cannot be left to chance and "close" is never close enough. Businesses need complete control over their projects, even if they are being outsourced. Mechanical engineers use the core principles as well as other knowledge in the field to design.

A Mechanical Engineer will:

~ Know how energy gets converted to useful power (thermodynamics).
~ Examine the wear and tear of machines and systems.
~ Prepare configurations and drawings of machines or machine parts.
~ Examine strength of material for a particular application.
~ Design advanced materials (machine design).

This article has been offer consideration of Mechanical 3d Modeling in http://www.mechanical3dmodelling.com/, Mechanical 3d Modeling, in Mechanical 3D Modeling Services more than 10 years.

Article Source: http://EzineArticles.com/?expert=Harvesh_V_Modh

Labels: ,

Mechanical Engineering involves the Physical usage for mechanism and functioning, design, manufacturing, installation, operation and maintenance of mechanical systems such as boilers, condensers, heat engines, air conditioners & refrigerators, machine tools, thermal power stations etc.

Kinematics, dynamics, static, Energy conversion, Mechanics, Manufacturing and production, refrigeration and air conditioning are the foundation subjects of mechanical engineering. It also Engage its attention with other Engineering disciplines like Electrical engineering in electronics, Aeronautical Engineering in Fluid Mechanics, Civil Engineering in stress & Strain analysis, Computer Engineering in hardware manufacturing etc.

Accomplishing mechanical projects has always posed serious problems for companies, whether they need computer aided design such as electrical engineering, new industrial product design, or civil engineering of a new building.

Many people are familiar with online project marketplaces that connect businesses and individuals in need of services with skilled professionals to perform the work. Companies have long struggled with the engineering required to launch new products and build customized facilities. When you discuss the actual mechanical design of your next key product, or the structural engineering of a multi million dollar building, things cannot be left to chance and "close" is never close enough. Businesses need complete control over their projects, even if they are being outsourced. Mechanical engineers use the core principles as well as other knowledge in the field to design.

A Mechanical Engineer will:

~ Know how energy gets converted to useful power (thermodynamics).
~ Examine the wear and tear of machines and systems.
~ Prepare configurations and drawings of machines or machine parts.
~ Examine strength of material for a particular application.
~ Design advanced materials (machine design).

This article has been offer consideration of Mechanical 3d Modeling in http://www.mechanical3dmodelling.com/, Mechanical 3d Modeling, in Mechanical 3D Modeling Services more than 10 years.

Article Source: http://EzineArticles.com/?expert=Harvesh_V_Modh

Labels: ,

Mechanical Engineering Online

Online Mechanical Engineering School programs are available at the bachelor level, the master's level, and the doctorate level. The discipline of Mechanical Engineering is among the oldest in the field of engineering and emphasizes an suitable mix of energy science and technology, applied mechanics, thermal sciences, and design.

Online Bachelor of Science in Mechanical Engineering programs are designed to provide students with comprehensive backgrounds for a broad spectrum of engineering careers. Mechanical Engineering requires an academic degree in science, and they use acquired scientific knowledge in the process of design and development.

A degree in Mechanical Engineering is applicable almost anywhere. Mechanical Engineers work in manufacturing, industrial plants, laboratories, on construction sites, in private engineering firms, and government agencies. Mechanical Engineers may be responsible for preparing preliminary and detailed design drawings, product specifications, and functions of products; finding creative to practical and technological problems; and testing and evaluation of all components of product efficacy, and they ensure the safety and performance of product design.

A degree in Mechanical Engineering requires courses in calculus, biology, physics, fluid mechanics, technical writing, and computer design. Mechanical Engineering involves research, product design and development, manufacturing, testing, operation, and maintenance.

Masters and doctorate degrees in Mechanical Engineering require higher level studies in all subjects, research, and a thesis. Graduate degrees in Mechanical Engineering allow advanced duties and responsibilities in the workplace. Advanced degrees in Mechanical Engineering may also allow the move into management or sales, in which cases, the engineering background enables detailed discussion of technical aspects and aids in product design, planning, installation, and use.

You can find an Online Mechanical Engineering School by searching the many options here at www.schoolsgalore.com.

Copyright 2006 - All Rights Reserved

Michael Bustamante, in association with Media Positive Communications, Inc. for SchoolsGalore.com

M. Bustamante is a staff writer for Media Positive Communications, Inc. in association with SchoolsGalore.com. Find Mechanical Engineering Online at SchoolsGalore.com; meeting your needs as your educational resource to locate schools

Article Source: http://EzineArticles.com/?expert=Michael_Bustamante

Labels: ,

Online Mechanical Engineering School programs are available at the bachelor level, the master's level, and the doctorate level. The discipline of Mechanical Engineering is among the oldest in the field of engineering and emphasizes an suitable mix of energy science and technology, applied mechanics, thermal sciences, and design.

Online Bachelor of Science in Mechanical Engineering programs are designed to provide students with comprehensive backgrounds for a broad spectrum of engineering careers. Mechanical Engineering requires an academic degree in science, and they use acquired scientific knowledge in the process of design and development.

A degree in Mechanical Engineering is applicable almost anywhere. Mechanical Engineers work in manufacturing, industrial plants, laboratories, on construction sites, in private engineering firms, and government agencies. Mechanical Engineers may be responsible for preparing preliminary and detailed design drawings, product specifications, and functions of products; finding creative to practical and technological problems; and testing and evaluation of all components of product efficacy, and they ensure the safety and performance of product design.

A degree in Mechanical Engineering requires courses in calculus, biology, physics, fluid mechanics, technical writing, and computer design. Mechanical Engineering involves research, product design and development, manufacturing, testing, operation, and maintenance.

Masters and doctorate degrees in Mechanical Engineering require higher level studies in all subjects, research, and a thesis. Graduate degrees in Mechanical Engineering allow advanced duties and responsibilities in the workplace. Advanced degrees in Mechanical Engineering may also allow the move into management or sales, in which cases, the engineering background enables detailed discussion of technical aspects and aids in product design, planning, installation, and use.

You can find an Online Mechanical Engineering School by searching the many options here at www.schoolsgalore.com.

Copyright 2006 - All Rights Reserved

Michael Bustamante, in association with Media Positive Communications, Inc. for SchoolsGalore.com

M. Bustamante is a staff writer for Media Positive Communications, Inc. in association with SchoolsGalore.com. Find Mechanical Engineering Online at SchoolsGalore.com; meeting your needs as your educational resource to locate schools

Article Source: http://EzineArticles.com/?expert=Michael_Bustamante

Labels: ,

Monday, August 25, 2008

The Advantages of Metal Rollforming Over Traditional Pipe and Tube Making

Rollforming (sometimes also termed open section forming) employs a series of sets of dies in order to bend a sheet of metal little by little until the desired profile (cross section) is obtained. Rollforming is a continuous operation of bending in which a long metal strip or sheet- usually of coiled steel - is passed through sets of rolls (or stands), each of which performs only a small incremental portion of the bend until the finished cross section profile is achieved. Roll forming is especially useful in the production of parts of long length, and in large quantities. Metal rollforming is quite like traditional pipe and tube making. However, rollforming is able to create more complicated profiles. In both pipe and tube making and in roll forming metal sheets are bent with roller dies, in which each roll pair works the sheet progressively until the final shape is obtained. Rollforming differs from the older techniques in that it can be combined with prepunching, postpunching, and midpiercing inline, together with sweeping prior to cutoff.

Another advantage of rollforming is that the same rollforming machinery can be used to produce a wide variety of cross section profiles. Each different profile requires a specially designed set of rolls. The fundamental roll design resembles a flower - i.e. a sequence of profile cross sections (one for each set of rolls). Because rollforming is an exact operation and involves high machinery costs, computer simulation is used in order to validate the design of the roll stands to make sure that the metal product won't be stressed unduly, and also to minimize the total number of rolls required. Examples of rollformed applications include automobile chassis sections, window guides, and impact bars. These can be prepunched, then rollformed, midpierced inline, rollformed some more, and then welded and cut off in one continuous operation.

As in pipe and tube mills, rollforming can be used with practically all metals, nonferrous as well as ferrous. Coils of stainless steel, high strength and low alloy steel, martensitic steel, as well as aluminum can be rollformed. It is possible to emboss coils of aluminum or steel with finishes that simulate wood grain (e.g. for garage doors). When using embossed metals the roller dies must be adjusted so as not to roll out the embossment. Prepainted and vinyl laminated sheets can also be rollformed but not welded. Rollforming is a process of great versatility which permits innovative design. Setting a rollforming system up requires a skilled rollform engineer's expertise, as well as considerable collaboration between the manufacturer and the vendor in order to develop a successful product.

No matter what your particular metal rollforming application demands, Samco's experienced and highly trained staff of experienced professionals are the world leaders in state-of-the-art rollform design and installation. Choice of the correct equipment for the job, skillful design of the tooling and product, thorough training of the rollforming machinery operators, and vigilant maintenance of the rollforming system are our specialty.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

Rollforming (sometimes also termed open section forming) employs a series of sets of dies in order to bend a sheet of metal little by little until the desired profile (cross section) is obtained. Rollforming is a continuous operation of bending in which a long metal strip or sheet- usually of coiled steel - is passed through sets of rolls (or stands), each of which performs only a small incremental portion of the bend until the finished cross section profile is achieved. Roll forming is especially useful in the production of parts of long length, and in large quantities. Metal rollforming is quite like traditional pipe and tube making. However, rollforming is able to create more complicated profiles. In both pipe and tube making and in roll forming metal sheets are bent with roller dies, in which each roll pair works the sheet progressively until the final shape is obtained. Rollforming differs from the older techniques in that it can be combined with prepunching, postpunching, and midpiercing inline, together with sweeping prior to cutoff.

Another advantage of rollforming is that the same rollforming machinery can be used to produce a wide variety of cross section profiles. Each different profile requires a specially designed set of rolls. The fundamental roll design resembles a flower - i.e. a sequence of profile cross sections (one for each set of rolls). Because rollforming is an exact operation and involves high machinery costs, computer simulation is used in order to validate the design of the roll stands to make sure that the metal product won't be stressed unduly, and also to minimize the total number of rolls required. Examples of rollformed applications include automobile chassis sections, window guides, and impact bars. These can be prepunched, then rollformed, midpierced inline, rollformed some more, and then welded and cut off in one continuous operation.

As in pipe and tube mills, rollforming can be used with practically all metals, nonferrous as well as ferrous. Coils of stainless steel, high strength and low alloy steel, martensitic steel, as well as aluminum can be rollformed. It is possible to emboss coils of aluminum or steel with finishes that simulate wood grain (e.g. for garage doors). When using embossed metals the roller dies must be adjusted so as not to roll out the embossment. Prepainted and vinyl laminated sheets can also be rollformed but not welded. Rollforming is a process of great versatility which permits innovative design. Setting a rollforming system up requires a skilled rollform engineer's expertise, as well as considerable collaboration between the manufacturer and the vendor in order to develop a successful product.

No matter what your particular metal rollforming application demands, Samco's experienced and highly trained staff of experienced professionals are the world leaders in state-of-the-art rollform design and installation. Choice of the correct equipment for the job, skillful design of the tooling and product, thorough training of the rollforming machinery operators, and vigilant maintenance of the rollforming system are our specialty.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

Making History With a State-of-the-Art Roll Former Machine

Modern roll forming dates from the post World War II era, with the introduction of rotary encoders, pneumatic presses, prepunching and in-line welding, as well as technology which allowed the roll forming of prepainted metal. In the 1970's and 1980's gagged punches made prepunching more sophisticated, and tool changeover downtime was reduced through the use of side by side rolls, rafted construction, and other innovations. By the 1990's computer assisted roll former machine design systems were introduced, and since that time many programmable controllers and computer systems have greatly increased efficiency and product quality.

An example is the double duplex roll forming mill, which has a duplex roll former upstream followed by a duplex roll former downstream on the same base. The upstream mill controls the leg or flange height by gliding in and out, while the downstream mill controls the width of the web in the same fashion. An example of this type of roll former is the Studmaker, which represents the latest in technological innovation: changes in the height of the flange or the width of the web can be made in less than twenty minutes. Steel studs can be produced in both English and metric sizes without roll or cut off die changes. The Studmaker is a pre-cut operation which eliminates the need for cutoff dies and diary pairs. Material sizes varying from 12 to 20 gauge, and stud sizes varying from 3-5/8 inches to 14 inches, enable the manufacturer to produce steel framing, light drywall stud and load-bearing stud, slip track and heavy 12-gauge joist, on the same machine with minimal changeover downtime. Minimizing changeover downtime is especially cost effective for relatively small orders - the Studmaker can be retooled in less than twenty minutes, where older roll former machines required up to eight hours setup time to make the same change.

New roll forming technology permits similar products - such as cee and zee profiles - to be produced on the same set of rolls. This is done by splitting the mill along its center, and setting the flange, web, and ear sizes using a control panel which can move the mill rafts to change the sizes. It is even possible to change profiles at the touch of a button. For example, the Purlinmaster can roll form cee profile purlins, and can be retooled to roll form zee profile purlins in only 7 seconds. Besides cee and zee profile purlins, this roll former can also produce lipped and u channel profiles. Web width and flange height can be changed in minutes instead of the hours required by conventional roll formers. The Purlinmaster also has an auto-gauging feature which permits the operator to change from one coil thickness to another without retooling at all - the new gauge can be selected immediately from the operator's control console. The Purlinmaster can produce prepainted purlin as well as galvanized and hot rolled black steel, at speeds up to 180 fpm and with a wide variety of hole punching options for inline flange and web hole punching of the highest accuracy.

When you are ready for the latest in roll former machine technology, let Samco's expert staff help you plan and select the ideal machinery for your needs. Our Studmaker and Purlinmaster are on the cutting edge of roll forming history.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

Modern roll forming dates from the post World War II era, with the introduction of rotary encoders, pneumatic presses, prepunching and in-line welding, as well as technology which allowed the roll forming of prepainted metal. In the 1970's and 1980's gagged punches made prepunching more sophisticated, and tool changeover downtime was reduced through the use of side by side rolls, rafted construction, and other innovations. By the 1990's computer assisted roll former machine design systems were introduced, and since that time many programmable controllers and computer systems have greatly increased efficiency and product quality.

An example is the double duplex roll forming mill, which has a duplex roll former upstream followed by a duplex roll former downstream on the same base. The upstream mill controls the leg or flange height by gliding in and out, while the downstream mill controls the width of the web in the same fashion. An example of this type of roll former is the Studmaker, which represents the latest in technological innovation: changes in the height of the flange or the width of the web can be made in less than twenty minutes. Steel studs can be produced in both English and metric sizes without roll or cut off die changes. The Studmaker is a pre-cut operation which eliminates the need for cutoff dies and diary pairs. Material sizes varying from 12 to 20 gauge, and stud sizes varying from 3-5/8 inches to 14 inches, enable the manufacturer to produce steel framing, light drywall stud and load-bearing stud, slip track and heavy 12-gauge joist, on the same machine with minimal changeover downtime. Minimizing changeover downtime is especially cost effective for relatively small orders - the Studmaker can be retooled in less than twenty minutes, where older roll former machines required up to eight hours setup time to make the same change.

New roll forming technology permits similar products - such as cee and zee profiles - to be produced on the same set of rolls. This is done by splitting the mill along its center, and setting the flange, web, and ear sizes using a control panel which can move the mill rafts to change the sizes. It is even possible to change profiles at the touch of a button. For example, the Purlinmaster can roll form cee profile purlins, and can be retooled to roll form zee profile purlins in only 7 seconds. Besides cee and zee profile purlins, this roll former can also produce lipped and u channel profiles. Web width and flange height can be changed in minutes instead of the hours required by conventional roll formers. The Purlinmaster also has an auto-gauging feature which permits the operator to change from one coil thickness to another without retooling at all - the new gauge can be selected immediately from the operator's control console. The Purlinmaster can produce prepainted purlin as well as galvanized and hot rolled black steel, at speeds up to 180 fpm and with a wide variety of hole punching options for inline flange and web hole punching of the highest accuracy.

When you are ready for the latest in roll former machine technology, let Samco's expert staff help you plan and select the ideal machinery for your needs. Our Studmaker and Purlinmaster are on the cutting edge of roll forming history.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

Modern Purlinmaster and Studmaker Rollformer Technology Means Bigger Savings For You!

As a manufacturer of rolled steel components such as studs, tracks, joists, cee and zee purlins, and roof trusses, you know that one of your biggest headaches is machine and technician downtime while changing product lines. Changing from one product profile to another - or even adjusting for changes in the thickness of the material used with the same profile - can cause hours of downtime in which nothing is being manufactured. But now new technological breakthroughs can reduce or entirely eliminate difficulties in adjusting the die and roll tooling set ups, reduce errors caused by operators in the changeover, and eliminate wasted coils due to trial and error in the new set up. An example of recent breakthroughs in rollforming technology minimizing downtime is the Purlinmaster rollformer, which can be switched from a cee section profile to a zee section profile at the touch of a button (in seven seconds)! Both web width and flange height can be changed quickly, and material gauge can be changed at the touch of a button. The Purlinmaster also features a high speed hydraulic punch.

Changeover of product lines when the only difference between the profiles occurs in the middle or web area is easiest on a duplex or double duplex rollforming system. Here the roll tooling is split in two: half of the tooling is mounted on the inner side of the mill, and the other half is mounted on the outer side, such that the inner and outer portions of the mill move towards or away from one another. The inner side is fixed and the outer side glides; or, it can be centerline compatible. This makes changeover from a smaller to larger stud web size possible just at the touch of a button. A state-of-the-art Studmaker rollformer can be completely changed by electro-mechanical adjustment to produce a different flange height with a different width in a different material gauge in less than twenty minutes! In line dies can be changed in three minutes. Moreover, the Studmaker rollformer can be integrated with your existing piercing and cut off equipment to minimize your investment. And speaking of minimizing your investment, consider an Ironclad rollformer for producing panels in a great variety of profiles, including customized profiles to your specifications. These inexpensive rollformers provide variable speed control as well as programmable length options, and flying shear makes continuous, non stop production possible.

When you are looking to minimize your costs from downtime, consider the Purlinmaster rollformer for manufacturing cee and zee purlins, and the unique Studmaker rollformer for studs and tracks. And if you are ready for the latest technology at the lowest price, look to a Ironclad rollformer for producing custom profile panels. Samco means the latest technology to help you save money.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

As a manufacturer of rolled steel components such as studs, tracks, joists, cee and zee purlins, and roof trusses, you know that one of your biggest headaches is machine and technician downtime while changing product lines. Changing from one product profile to another - or even adjusting for changes in the thickness of the material used with the same profile - can cause hours of downtime in which nothing is being manufactured. But now new technological breakthroughs can reduce or entirely eliminate difficulties in adjusting the die and roll tooling set ups, reduce errors caused by operators in the changeover, and eliminate wasted coils due to trial and error in the new set up. An example of recent breakthroughs in rollforming technology minimizing downtime is the Purlinmaster rollformer, which can be switched from a cee section profile to a zee section profile at the touch of a button (in seven seconds)! Both web width and flange height can be changed quickly, and material gauge can be changed at the touch of a button. The Purlinmaster also features a high speed hydraulic punch.

Changeover of product lines when the only difference between the profiles occurs in the middle or web area is easiest on a duplex or double duplex rollforming system. Here the roll tooling is split in two: half of the tooling is mounted on the inner side of the mill, and the other half is mounted on the outer side, such that the inner and outer portions of the mill move towards or away from one another. The inner side is fixed and the outer side glides; or, it can be centerline compatible. This makes changeover from a smaller to larger stud web size possible just at the touch of a button. A state-of-the-art Studmaker rollformer can be completely changed by electro-mechanical adjustment to produce a different flange height with a different width in a different material gauge in less than twenty minutes! In line dies can be changed in three minutes. Moreover, the Studmaker rollformer can be integrated with your existing piercing and cut off equipment to minimize your investment. And speaking of minimizing your investment, consider an Ironclad rollformer for producing panels in a great variety of profiles, including customized profiles to your specifications. These inexpensive rollformers provide variable speed control as well as programmable length options, and flying shear makes continuous, non stop production possible.

When you are looking to minimize your costs from downtime, consider the Purlinmaster rollformer for manufacturing cee and zee purlins, and the unique Studmaker rollformer for studs and tracks. And if you are ready for the latest technology at the lowest price, look to a Ironclad rollformer for producing custom profile panels. Samco means the latest technology to help you save money.

Article Source: http://EzineArticles.com/?expert=Alice_Lane

Labels:

Tuesday, March 11, 2008

Nontraditional Metal Fabrication Machining Processes

Nontraditional metal fabrication machining processes are those that are new to the industry and do not always use machining forces and perishable tooling. These nontraditional processes often advance the metal fabrication industry by making it possible to cut materials that were formerly too difficult or impossible to work with. Some of these processes are becoming more widely used in the metal fabrication industry.

Abrasive Flow Machining

Abrasive flow machining is a complex process that directs a semisolid abrasive material back and forth between two opposing cylinders with block or sheet metal positioned in between. This process cuts through metals made of soft aluminum and nickel alloys.

Another form of metal fabrication processing using abrasive flow technology is abrasive jet machining. This process uses the same abrasive material, propelled at the metal at high velocities using a directed stream of compressed air or CO2. This is highly effective in deburring, cleaning and cutting parts. The abrasive materials can consist of silicon carbide, aluminum oxide, boron carbide or glass beads. The added use of compressed gas helps to keep the materials and the working environment cool during processing.

Laminated Object Manufacturing

The laminated object manufacturing metal fabrication process produces models from solid sheet materials. Solid sheet materials can be purchased in bulk and are cheaper than other types of production materials. The process uses a three dimensional electronic file and laser applications to create the machining effect. Drilling, welding, engraving and case-hardening can all be completed using these lasers. Intense pulsed beams of light created by carbon dioxide lasers are often used. Compressed air, argon, oxygen and nitrogen are also used in laminated object manufacturing.

Reverse Engineering

Reverse engineering is a metal fabrication process that utilizes lasers, CMM and other measuring devices to create a computer assisted design file from an existing part. This 'scanning' of an existing part allows the operator to precisely reproduce the existing part, repair any flaws by altering the production of the new part or to redesign an entirely new part based on the substructure of the scanned part. It is a very useful nontraditional process for companies that develop new parts and seek to improve on existing designs.

Thermal Energy Finishing

Thermal energy finishing uses thermal energy and the resulting heat to quickly and accurately burn away the unwanted flash material and burrs from around finished parts. This finishing process is ideal for use with parts that are used to conduct fluids or gases. It also consistently produces a quality product that is free of contaminates. This in turn reduces the need for wasted metal fabrication materials due to inaccurate parts and eliminates the need for extensive quality control checks.

Nontraditional metal fabrication machining processes are those that are new to the industry and do not always use machining forces and perishable tooling. These nontraditional processes often advance the metal fabrication industry by making it possible to cut materials that were formerly too difficult or impossible to work with. Some of these processes are becoming more widely used in the metal fabrication industry.

Abrasive Flow Machining

Abrasive flow machining is a complex process that directs a semisolid abrasive material back and forth between two opposing cylinders with block or sheet metal positioned in between. This process cuts through metals made of soft aluminum and nickel alloys.

Another form of metal fabrication processing using abrasive flow technology is abrasive jet machining. This process uses the same abrasive material, propelled at the metal at high velocities using a directed stream of compressed air or CO2. This is highly effective in deburring, cleaning and cutting parts. The abrasive materials can consist of silicon carbide, aluminum oxide, boron carbide or glass beads. The added use of compressed gas helps to keep the materials and the working environment cool during processing.

Laminated Object Manufacturing

The laminated object manufacturing metal fabrication process produces models from solid sheet materials. Solid sheet materials can be purchased in bulk and are cheaper than other types of production materials. The process uses a three dimensional electronic file and laser applications to create the machining effect. Drilling, welding, engraving and case-hardening can all be completed using these lasers. Intense pulsed beams of light created by carbon dioxide lasers are often used. Compressed air, argon, oxygen and nitrogen are also used in laminated object manufacturing.

Reverse Engineering

Reverse engineering is a metal fabrication process that utilizes lasers, CMM and other measuring devices to create a computer assisted design file from an existing part. This 'scanning' of an existing part allows the operator to precisely reproduce the existing part, repair any flaws by altering the production of the new part or to redesign an entirely new part based on the substructure of the scanned part. It is a very useful nontraditional process for companies that develop new parts and seek to improve on existing designs.

Thermal Energy Finishing

Thermal energy finishing uses thermal energy and the resulting heat to quickly and accurately burn away the unwanted flash material and burrs from around finished parts. This finishing process is ideal for use with parts that are used to conduct fluids or gases. It also consistently produces a quality product that is free of contaminates. This in turn reduces the need for wasted metal fabrication materials due to inaccurate parts and eliminates the need for extensive quality control checks.

The Custom Metal Stamping Process

Today, manufacturing has embraced a wide range of advanced technologies that have enabled the reduction of turnaround time considerably. As a result, demand on the metal stamping industry has also increased as the components have to be made to be exactly suitable to the final product. This has made precision and custom metal stamping much more important in the manufacturing industry.

Custom metal stamping is the process of creating metal products according to the required sizes and shapes through a method called stamping. It involves the pressing or stamping of the metal in dies or press tools to give it the right shape. In custom metal stamping, the final products are made according to customer’s precise requirements and conditions. Custom metal stamping is used in various industries like construction, electrical, bearing, automotive, medical and janitorial, among others.

Metal stamping typically involves the normal process of metal stamping but with certain changes. These can be the change in the kind of metal to be used, changes in the size and shape of the final product, the need to produce many kinds of sizes and shapes, high quality of the tools used, the volume and the number of units to be produced, the kinds of presses required and the number of presses and dies required. Some producers are changing their processes to accommodate any volume, up to thousands of tons.

There are several challenges to be met by the custom metal stamping companies. These are producing a high quality product, designing new products or re-engineering existing products to suit customers’ needs while also meeting delivery requirements. The company has to be involved in every stage right from product design assistance to the final delivery. Additionally, the costs also have to be kept low even as the scope of offerings is increased.

Today, manufacturing has embraced a wide range of advanced technologies that have enabled the reduction of turnaround time considerably. As a result, demand on the metal stamping industry has also increased as the components have to be made to be exactly suitable to the final product. This has made precision and custom metal stamping much more important in the manufacturing industry.

Custom metal stamping is the process of creating metal products according to the required sizes and shapes through a method called stamping. It involves the pressing or stamping of the metal in dies or press tools to give it the right shape. In custom metal stamping, the final products are made according to customer’s precise requirements and conditions. Custom metal stamping is used in various industries like construction, electrical, bearing, automotive, medical and janitorial, among others.

Metal stamping typically involves the normal process of metal stamping but with certain changes. These can be the change in the kind of metal to be used, changes in the size and shape of the final product, the need to produce many kinds of sizes and shapes, high quality of the tools used, the volume and the number of units to be produced, the kinds of presses required and the number of presses and dies required. Some producers are changing their processes to accommodate any volume, up to thousands of tons.

There are several challenges to be met by the custom metal stamping companies. These are producing a high quality product, designing new products or re-engineering existing products to suit customers’ needs while also meeting delivery requirements. The company has to be involved in every stage right from product design assistance to the final delivery. Additionally, the costs also have to be kept low even as the scope of offerings is increased.

The Custom Metal Stamping Process

Today, manufacturing has embraced a wide range of advanced technologies that have enabled the reduction of turnaround time considerably. As a result, demand on the metal stamping industry has also increased as the components have to be made to be exactly suitable to the final product. This has made precision and custom metal stamping much more important in the manufacturing industry.

Custom metal stamping is the process of creating metal products according to the required sizes and shapes through a method called stamping. It involves the pressing or stamping of the metal in dies or press tools to give it the right shape. In custom metal stamping, the final products are made according to customer’s precise requirements and conditions. Custom metal stamping is used in various industries like construction, electrical, bearing, automotive, medical and janitorial, among others.

Metal stamping typically involves the normal process of metal stamping but with certain changes. These can be the change in the kind of metal to be used, changes in the size and shape of the final product, the need to produce many kinds of sizes and shapes, high quality of the tools used, the volume and the number of units to be produced, the kinds of presses required and the number of presses and dies required. Some producers are changing their processes to accommodate any volume, up to thousands of tons.

There are several challenges to be met by the custom metal stamping companies. These are producing a high quality product, designing new products or re-engineering existing products to suit customers’ needs while also meeting delivery requirements. The company has to be involved in every stage right from product design assistance to the final delivery. Additionally, the costs also have to be kept low even as the scope of offerings is increased.

Today, manufacturing has embraced a wide range of advanced technologies that have enabled the reduction of turnaround time considerably. As a result, demand on the metal stamping industry has also increased as the components have to be made to be exactly suitable to the final product. This has made precision and custom metal stamping much more important in the manufacturing industry.

Custom metal stamping is the process of creating metal products according to the required sizes and shapes through a method called stamping. It involves the pressing or stamping of the metal in dies or press tools to give it the right shape. In custom metal stamping, the final products are made according to customer’s precise requirements and conditions. Custom metal stamping is used in various industries like construction, electrical, bearing, automotive, medical and janitorial, among others.

Metal stamping typically involves the normal process of metal stamping but with certain changes. These can be the change in the kind of metal to be used, changes in the size and shape of the final product, the need to produce many kinds of sizes and shapes, high quality of the tools used, the volume and the number of units to be produced, the kinds of presses required and the number of presses and dies required. Some producers are changing their processes to accommodate any volume, up to thousands of tons.

There are several challenges to be met by the custom metal stamping companies. These are producing a high quality product, designing new products or re-engineering existing products to suit customers’ needs while also meeting delivery requirements. The company has to be involved in every stage right from product design assistance to the final delivery. Additionally, the costs also have to be kept low even as the scope of offerings is increased.

Sunday, March 02, 2008

Air Purifier & Air Cleaner OEM Production

Finding an OEM solution for air purifier & air cleaner, there are many companies out there who are committed to finding the right solution for you and your business. Most of them will develop a solution meeting your needs. Below are examples of solutions you may need to consider if you are seeking for air purifier OEM solutions. In developing new OEM products, your vendor will work with you through four phases:

Please note that There are two common types of air purifiers that can remove some or all of the particles in the air: mechanical filters—the most effective are classified as High Efficiency Particulate Air filters (HEPA filters)—and electrostatic precipitators. The Production procedures might be various depending on projects. HEPA filters are made out of very fine glass threads with a diameter of less than 1 micron. Electrostatic precipitators rely on electrostatic forces to remove particles from the air.

Phase 1: EVALUATION vendor and the OEM customers develop a detailed understanding of the product requirements. vendor then evaluates the business opportunity and technical feasibility.

Phase 2: DEVELOPMENT AND PROTOTYPE vendor works to achieve the required performance goals and to demonstrate and deliver a small number of prototype products in a relative short time.

Phase 3: PILOT PRODUCTION vendor resolves manufacturing issues, pursues opportunities for cost reduction, and scales up for production. Final qualification of the product design will occur. Additional testing protocols will be developed to address the quality and reliability as well during this phase.

Phase 4: FULL PRODUCTION vendor establishes the final manufacturing process and brings the new product into full volume production.

Finding an OEM solution for air purifier & air cleaner, there are many companies out there who are committed to finding the right solution for you and your business. Most of them will develop a solution meeting your needs. Below are examples of solutions you may need to consider if you are seeking for air purifier OEM solutions. In developing new OEM products, your vendor will work with you through four phases:

Please note that There are two common types of air purifiers that can remove some or all of the particles in the air: mechanical filters—the most effective are classified as High Efficiency Particulate Air filters (HEPA filters)—and electrostatic precipitators. The Production procedures might be various depending on projects. HEPA filters are made out of very fine glass threads with a diameter of less than 1 micron. Electrostatic precipitators rely on electrostatic forces to remove particles from the air.

Phase 1: EVALUATION vendor and the OEM customers develop a detailed understanding of the product requirements. vendor then evaluates the business opportunity and technical feasibility.

Phase 2: DEVELOPMENT AND PROTOTYPE vendor works to achieve the required performance goals and to demonstrate and deliver a small number of prototype products in a relative short time.

Phase 3: PILOT PRODUCTION vendor resolves manufacturing issues, pursues opportunities for cost reduction, and scales up for production. Final qualification of the product design will occur. Additional testing protocols will be developed to address the quality and reliability as well during this phase.

Phase 4: FULL PRODUCTION vendor establishes the final manufacturing process and brings the new product into full volume production.

Choosing Quality Industrial Steel Shelving

There are many different manufacturers of Industrial Steel Shelving in the market today. The trouble is picking quality shelving at a reasonable price. The Prices of a shelf depending on the manufacturer can vary greatly and so can the quality. Your cheapest product is currently coming out of China where this type of shelving is mass produced in great quantities. You will also see some cheaper versions of Industrial type shelf's at places like Wal-Mart.

The problem with cheap Shelf's is that they may look industrial but they are not able to handle the weight of a true quality shelf. Generally the life expectancy of the shelf is greatly reduced because the cheap versions tend to twist up much easier when put under heavy weight. Therefore if you are going to put out some money to put some shelving in your warehouse or office space you want to find cheap or reasonably priced steel shelving that is made from quality materials and is truly made to be used in industrial applications.

Quality Industrial Steel Shelving is generally made from 18 gauge or 20 gauge cold rolled steel. What you will find is that some of the cheap versions you will run in to are made from steel that is not thick enough to handle the weight. For a durable paint job shelf's of this type are usually phosphated and then painted with a baked on enamel to ensure a lasting finish. Weight capacity of a quality unit is generally in between 450 to 2000 pounds. The heavier the load requirement the more reinforced the unit has to be. Usually 12 gauge angle bars are used to reinforce the shelving so it can handle heavier weights.

Industrial Steel Shelving is available in a large variety of sizes. Also their are open and closed units depending on your needs. The open units are accessible from both sides where the closed units are made with a back plate and can only be accessed from one side, however closed industrial steel shelving units are more durable and can also be separated in to bins for storing smaller items like screws or such. Generally shelf's of this type come in 5 to 10 shelf units depending on your storage needs.

Wide span Industrial Steel Shelving is made to storing large items in warehouses and can also be used for making tire racks. Tire racks are generally just widespan shelving units without any decking. The shelving is made in a width to accommodate a tire. Wide span shelving is quite sturdy and is perfect for storing heavier load like car parts and such. Widespan Shelving usually comes in anywhere from 3 to 6 levels. Sizes range from 36X12X84 to 96X48X84. Since this type of a shelving unit is used to hold heavier loads it is usually decked with 5/8" particle board but it can also be decked with a wire mesh or any other material that can be cut to size. Tire racks of course do not require decking. A good quality Wide span Shelf is made from cold rolled steel which is then phosphated and then painted with a baked on enamel.

Be weary of Industrial steel shelving that is so cheap that it beats the going market price. Usually when the units are so cheap the quality of the materials used are reflected in that discounted price. Remember that this type of shelving is made from steel and steel prices tend to fluctuate so prices may also vary. However if you find a unit that is made from good quality heavy gauge steel that is cold rolled you are on the right track to getting a quality shelf at a reasonable price

There are many different manufacturers of Industrial Steel Shelving in the market today. The trouble is picking quality shelving at a reasonable price. The Prices of a shelf depending on the manufacturer can vary greatly and so can the quality. Your cheapest product is currently coming out of China where this type of shelving is mass produced in great quantities. You will also see some cheaper versions of Industrial type shelf's at places like Wal-Mart.

The problem with cheap Shelf's is that they may look industrial but they are not able to handle the weight of a true quality shelf. Generally the life expectancy of the shelf is greatly reduced because the cheap versions tend to twist up much easier when put under heavy weight. Therefore if you are going to put out some money to put some shelving in your warehouse or office space you want to find cheap or reasonably priced steel shelving that is made from quality materials and is truly made to be used in industrial applications.

Quality Industrial Steel Shelving is generally made from 18 gauge or 20 gauge cold rolled steel. What you will find is that some of the cheap versions you will run in to are made from steel that is not thick enough to handle the weight. For a durable paint job shelf's of this type are usually phosphated and then painted with a baked on enamel to ensure a lasting finish. Weight capacity of a quality unit is generally in between 450 to 2000 pounds. The heavier the load requirement the more reinforced the unit has to be. Usually 12 gauge angle bars are used to reinforce the shelving so it can handle heavier weights.

Industrial Steel Shelving is available in a large variety of sizes. Also their are open and closed units depending on your needs. The open units are accessible from both sides where the closed units are made with a back plate and can only be accessed from one side, however closed industrial steel shelving units are more durable and can also be separated in to bins for storing smaller items like screws or such. Generally shelf's of this type come in 5 to 10 shelf units depending on your storage needs.

Wide span Industrial Steel Shelving is made to storing large items in warehouses and can also be used for making tire racks. Tire racks are generally just widespan shelving units without any decking. The shelving is made in a width to accommodate a tire. Wide span shelving is quite sturdy and is perfect for storing heavier load like car parts and such. Widespan Shelving usually comes in anywhere from 3 to 6 levels. Sizes range from 36X12X84 to 96X48X84. Since this type of a shelving unit is used to hold heavier loads it is usually decked with 5/8" particle board but it can also be decked with a wire mesh or any other material that can be cut to size. Tire racks of course do not require decking. A good quality Wide span Shelf is made from cold rolled steel which is then phosphated and then painted with a baked on enamel.

Be weary of Industrial steel shelving that is so cheap that it beats the going market price. Usually when the units are so cheap the quality of the materials used are reflected in that discounted price. Remember that this type of shelving is made from steel and steel prices tend to fluctuate so prices may also vary. However if you find a unit that is made from good quality heavy gauge steel that is cold rolled you are on the right track to getting a quality shelf at a reasonable price

Tuesday, February 26, 2008

Innovative Industrial Name Plates For Your Brand Establishment

Industrial name plate is a vital industrial product identification tool. Each product needs to be identified, for this name plates are attached or printed directly on it. The design of industrial name plate is very important as the nameplate mirrors the image of an industry and its products. It should have a unique quality, sustainability, finishing and character to stand apart; it should not be a run of the mill product. The brand should be portrayed in such a way that it should enhance the quality of a product; it should become a household name.

Nameplates and their vast utility:

Name plates are useful for customer information as well as for the service technicians. The nameplates can be affixed to give warranty instructions, warnings, "how to use" instructions or important data and contact numbers. Custom name plates help in maintenance also as equipment setting information, specifications and troubleshooting instructions etc are engraved on the custom nameplates.

There are various nameplate companies dealing in custom tags, FAA tags, control panels, dials and gauges. For vehicle industries like truck, tanker and trailer manufacturers, Vehicle Identification tags and assembly information, dial indicators for temperature, oil, liquid and vapor, emergency and prevention custom labels with vehicle maintenance and warranty information, nameplates are used on front panels of electronics, motherboards, and other equipments, which have to bear electrostatic discharge and heat dissipation, custom name plates for inspection and certification, safety tags, repair information tags, attention and caution plates, logos for compressor, conveyer, gearbox etc; multi-language operating information for oilfield equipment manufacturers etc.

Materials to bear toughest environments:

Nameplates can be of different materials according to the conditions, which they have to withstand. The industrial name plates need to survive industrial solvents, chemicals and many other physical abrasions like rain water, corrosion, heat or sun exposure etc. Therefore, durability of nametags should be the first thing to be considered while selecting the material. One can use metals, non-metals, plastics, and alloys like stainless steel, brass, and bronze as per industrial specifications. Silver anodized aluminum is considered best; brands sign or logos engraved in it last for long. Polycarbonate and lexan nameplates also have a good market. For the printing purposes any of the processes like die-cast, chemical etching, screen printing etc can be used.
Industrial name plate is a vital industrial product identification tool. Each product needs to be identified, for this name plates are attached or printed directly on it. The design of industrial name plate is very important as the nameplate mirrors the image of an industry and its products. It should have a unique quality, sustainability, finishing and character to stand apart; it should not be a run of the mill product. The brand should be portrayed in such a way that it should enhance the quality of a product; it should become a household name.

Nameplates and their vast utility:

Name plates are useful for customer information as well as for the service technicians. The nameplates can be affixed to give warranty instructions, warnings, "how to use" instructions or important data and contact numbers. Custom name plates help in maintenance also as equipment setting information, specifications and troubleshooting instructions etc are engraved on the custom nameplates.

There are various nameplate companies dealing in custom tags, FAA tags, control panels, dials and gauges. For vehicle industries like truck, tanker and trailer manufacturers, Vehicle Identification tags and assembly information, dial indicators for temperature, oil, liquid and vapor, emergency and prevention custom labels with vehicle maintenance and warranty information, nameplates are used on front panels of electronics, motherboards, and other equipments, which have to bear electrostatic discharge and heat dissipation, custom name plates for inspection and certification, safety tags, repair information tags, attention and caution plates, logos for compressor, conveyer, gearbox etc; multi-language operating information for oilfield equipment manufacturers etc.

Materials to bear toughest environments:

Nameplates can be of different materials according to the conditions, which they have to withstand. The industrial name plates need to survive industrial solvents, chemicals and many other physical abrasions like rain water, corrosion, heat or sun exposure etc. Therefore, durability of nametags should be the first thing to be considered while selecting the material. One can use metals, non-metals, plastics, and alloys like stainless steel, brass, and bronze as per industrial specifications. Silver anodized aluminum is considered best; brands sign or logos engraved in it last for long. Polycarbonate and lexan nameplates also have a good market. For the printing purposes any of the processes like die-cast, chemical etching, screen printing etc can be used.

Industrial Ink Jet Printers

Industrial inkjet printers are used for different types of industries such as packaging, decorative material production, graphic arts, point of sale, and other industries in which the company specializes in providing complete solutions for digital printing onto a wide range of substrates. Ink used in these printers is cured with ultra violet rays, which make them suitable for outdoor applications such as posters.

Most industrial inkjet printers do not require PCs to operate. A CD-ROM drive is preinstalled in these printers for loading print files (PRN) onto the internal hard drive. Other features include ink detection system, which is used to check exactly how much ink is left in black and color ink cartridges. This information is displayed on a LCD screen. The detection system can also be programmed to automatically shut down printing operations if ink levels fall below a certain point. This utility helps in reducing wastage of printing substrate due to dried up ink cartridges.

Some industrial inkjet printers are connected to a single computer or a network of computers. In large organizations, they are used as central printing devices and processes printing orders received from any device present in the network. This helps in reducing costs as a single printer takes care of all the printing needs of the organization.

These printers are used in conjunction with print software that enables users to import and edit images from different sources and create a variety of text and graphics. Printed substrate material is passed through warm air chambers to enable quick drying and prevent smudging of printed images.

Industrial inkjet printers provide the economical benefits of printing in bulk. They have enabled many small and large-scale companies to reduce printing costs and improve profitability. Increasing demand for printing activities has forced copier companies to increase printing capacity. This has created the demand for industrial inkjet printers, which is expected to increase in the coming years.
Industrial inkjet printers are used for different types of industries such as packaging, decorative material production, graphic arts, point of sale, and other industries in which the company specializes in providing complete solutions for digital printing onto a wide range of substrates. Ink used in these printers is cured with ultra violet rays, which make them suitable for outdoor applications such as posters.

Most industrial inkjet printers do not require PCs to operate. A CD-ROM drive is preinstalled in these printers for loading print files (PRN) onto the internal hard drive. Other features include ink detection system, which is used to check exactly how much ink is left in black and color ink cartridges. This information is displayed on a LCD screen. The detection system can also be programmed to automatically shut down printing operations if ink levels fall below a certain point. This utility helps in reducing wastage of printing substrate due to dried up ink cartridges.

Some industrial inkjet printers are connected to a single computer or a network of computers. In large organizations, they are used as central printing devices and processes printing orders received from any device present in the network. This helps in reducing costs as a single printer takes care of all the printing needs of the organization.

These printers are used in conjunction with print software that enables users to import and edit images from different sources and create a variety of text and graphics. Printed substrate material is passed through warm air chambers to enable quick drying and prevent smudging of printed images.

Industrial inkjet printers provide the economical benefits of printing in bulk. They have enabled many small and large-scale companies to reduce printing costs and improve profitability. Increasing demand for printing activities has forced copier companies to increase printing capacity. This has created the demand for industrial inkjet printers, which is expected to increase in the coming years.